How do I get my Honeywell thermostat off wait?
The "Wait" message on a Honeywell Thermostat means the thermostat is waiting to activate the HVAC system. This is done to prevent damaging the HVAC system compressor. If the system is working properly, then "Wait" should disappear after a few minutes. It will then resume normal operation.
A Hold message on a Honeywell Thermostat tells the thermostat to maintain the HVAC system for the building at a set temperature. The temperature will be maintained until the Hold expires or the temperature is manually changed. A Hold can be temporary or permanent depending on its setting.
Each thermostat model has a different display message when a delay occurs. This delay can be up to five minutes under normal operating conditions. A delay is used to protect your heating and cooling equipment from coming on too quickly (known as short cycling), which can cause damage.
Waiting means the thermostat has a heating, cooling, or ventilation request and is waiting to get confirmation from another Pelican device that the cycle is active.
This is where the “Hold” button on your thermostat comes into play. By pressing “Hold”, your thermostat will lock in the temperature it's currently at until you change it again. When you are ready for your normal schedule to resume, simply press the “Run” button and return to your typical programming.
A temporary hold will keep the HVAC system set to the held temperature for a temporary period of time of less than 12 hours or until the hold is cancelled. A permanent hold will keep the HVAC system set to the held temperature permanently, until the hold is cancelled.
Keeping your home at a constant temperature generally means that your HVAC system will run constantly to meet it. This means that your furnace or air conditioner may run when you're asleep, at work, or out of the house. This wastes more energy than the minimal amount that you might save by having it constantly run.
Occasionally, low battery power will lead to malfunctions in a thermostat including making it so that the thermostat won't change temperature settings when you want it to.
Look to see if the coolant is swirling/flowing immediately — that means the thermostat's stuck open. If the coolant doesn't flow after 10 minutes or so and continues to be stagnant after the temperature gauge indicates it's hot, the thermostat's likely stuck closed.
- Thermostat Has No Power. ...
- AC or Furnace Won't Turn On. ...
- Heater or AC Won't Turn Off. ...
- Thermostat Doesn't Match Room Temperature. ...
- Thermostat Doesn't Respond. ...
- Short Cycling. ...
- Thermostat Forgets Programmed Settings.
What happens when thermostat is stuck?
Due to corrosion or aging, your car's thermostat can get stuck in a closed position. If this happens, the thermostat will not let the coolant reach the radiator, and, as mentioned above, the engine will overheat, causing severe damage.
Try replacing the batteries, then check for a blown fuse or tripped breaker in the electrical panel. If the thermostat is still unresponsive, make sure the breaker is shut off and remove the cover.
Your Vents Are Blocked
Your thermostat will not be able to reach your desired temperature if you have something blocking the vents. Check the vents around your home and make sure you do not have any items such as furniture in the way of your vent's airflow. While you're at it, make sure all of your vents are open.
Troubleshooting a Programmable Honeywell Thermostat
Put in new batteries; Check the circuit breaker; Check the indoor unit to make sure all the panel doors are closed; Make sure the power is connected to the furnace or air conditioning unit by checking the switch near the indoor unit is up.
- Power off the thermostat and remove the batteries.
- Put the batteries in the wrong way, with negative to positive and positive to negative.
- Wait ten seconds and put them back in the correct way.
- Your thermostat will be reset to factory settings.
Keeping your thermostat in the AUTO position means less overall energy is being used—and that reduces your utility bills considerably. Not only that, your air filter will last longer than they will if you leave your fan running continuously—in other words, if you leave it in the “on” position.
A hold basically tells a thermostat to ignore any schedule that has been put in place and hold the HVAC system at a set temperature. Holds can be either temporary or permanent. A temporary hold has a set time when the hold will automatically expire. At that point, the thermostat will resume its normal schedule.
If you're going to be leaving your home or traveling for the winter, it's best to keep your thermostat set no lower than 55 degrees. If you don't, you could risk having your pipes freeze over.
- Press the up and fan button simultaneously. Continue pressing them together.
- In the meantime, change the right number to 1 and that of the left to 90.
- Now, press “Done”. You will have a reset machine.
It usually takes around two and a half to three and a half hours to cool your house from 80 to 72 degrees. However, a variety of different factors can affect the time it takes to reach the desired temperature, including the thermostat setting, the size of the house, and the efficiency of the air filters.
How do you know if your Honeywell thermostat is working?
Go to your thermostat and switch from Heating to Cooling and then feel the temperature of the air blowing from the vent. If COLD, this means your thermostat is cooling correctly, but the heating isn't working properly. Contact Support at 1-855-733-5465 to find a pro-installer in your area.
Type of thermostat being repaired or replaced.
Generally, repairing a thermostat costs around $200 to $500. This is the price range you'll find for most vehicles, although some may be higher or lower depending on the circumstances.
When a thermostat gets stuck open, it'll allow coolant to circulate continuously even when it's not needed. Unfortunately, that will overcool the engine and cause it to operate below its optimal temperature range. As a result, the engine will lose fuel efficiency, and its components will experience excess wear.
Modern home thermostats tend to have about a 10-year lifespan but are usually replaced sooner due to innovations in the market. Non-programmable thermostats have become outdated and replaced by programmable (or learning) thermostats.
The Thermostat Batteries Died and Need to be Replaced
If your thermostat is blank, the first thing you should do is check the batteries. Chances are, the batteries have died and the thermostat simply can't power on. Replace the batteries and see if your thermostat turns back on.
No power: If the thermostat isn't working at all, there could be a power issue. Try checking the circuit breaker box or replacing the batteries. Bad wiring: The thermostat may be unresponsive if the wiring has gone bad. Remove the cover and check inside for loose, detached, or corroded wires.
Standard thermostats: Enlist a friend or family member to assist, Position one person by the thermostat and one person by the furnace. Slowly turn the thermostat from off to heat and increase the temperature. Both the thermostat and furnace should make a sound.
The method to reset your thermostat will vary depending on the model. Common methods for resetting a thermostat include installing the battery backward for five seconds, pushing a recessed reset button with a pin or paper clip, or shutting off the breaker to the thermostat for 30 seconds.
As with all other systems, your thermostat will eventually become old and outdated. The lifespan of most home thermostats is 10 years. However, you may need to replace yours sooner as newer, more efficient thermostats enter the market.
A Malfunctioning Fan. A dysfunctional fan can be why your thermostat won't change temperature. This problem prevents the furnace system from forcing heated air into your home. Solution: switch off the furnace, wait two minutes, then switch off the fan.
How do you fix a thermostat that won t change the temperature?
The solution is equally simple: try replacing the batteries to see if your thermostat powers back on. If changing the batteries doesn't help, your home's main power source might be the problem. If you can safely reach your circuit breaker, try flipping it on and off to get your thermostat up and running again.
More than likely the problem could be that your thermostat isn't properly working, and you just need to tweak it to make your system work at 100% again. If your thermostat is hard wired in double check the fuse or circuit breaker, if it is battery operated check to see if the batteries need to be replaced.
- Press the Menu Icon.
- Scroll down to “Thermostat Information.
- Record the “Date Code”
- Press the “back” arrow, then scroll down to “Installer Options”
- Enter the Date Code when prompted to “Enter your password”
- Select “Reset”
- Select “Factory Reset”
Honeywell thermostats have a low battery indicator light. Once this light comes on, you'll have about 60 days to replace the batteries.
Many digital programmable thermostats have a “hold” function, which can come in quite handy. The "hold" function basically lets you override the pre-set temperature and thermostat setting if your schedule changes.
Irregular Operating Temperatures
One of the most prevalent symptoms of thermostat failure is irregular operating temperatures. A stuck closed thermostat will cause engine temperatures to skyrocket, while a stuck open thermostat will cause an engine to run cool.