Honeywell thermostat says wait? (2024)

Table of Contents

Honeywell thermostat says wait?

The "Wait" message on a Honeywell Thermostat means the thermostat is waiting to activate the HVAC system. This is done to prevent damaging the HVAC system compressor. If the system is working properly, then "Wait" should disappear after a few minutes. It will then resume normal operation.

(Video) What Does It Mean When My T Stat Says Wait: What To Do When Thermostat Says Wait or Recovery
(The Air Of Authority)
How long does thermostat say wait?

Each thermostat model has a different display message when a delay occurs. This delay can be up to five minutes under normal operating conditions. A delay is used to protect your heating and cooling equipment from coming on too quickly (known as short cycling), which can cause damage.

(Video) How to Over-ride the settings on your Honeywell Thermostat
(Sherlock Homes Austin)
Why is my Honeywell thermostat stuck on hold?

A Hold message on a Honeywell Thermostat tells the thermostat to maintain the HVAC system for the building at a set temperature. The temperature will be maintained until the Hold expires or the temperature is manually changed. A Hold can be temporary or permanent depending on its setting.

(Video) Thermostat staying in a delay? Here is how to fix it
(HVAC Tech Tips)
What to do if thermostat is not communicating?

4 Steps for Troubleshooting Your Thermostat
  1. Reset the Thermostat. Like any other electronic device, sometimes a digital thermostat needs a reset to get it working properly again. ...
  2. Clean Out Dust and Corrosion. ...
  3. Test the Power and Wiring. ...
  4. Adjust the Heat Anticipator.
Mar 18, 2020

(Video) Honeywell TH 8000 Thermostat - Service Champions
(Service Champions Plumbing, Heating & AC)
Why is my thermostat waiting?

Waiting means the thermostat has a heating, cooling, or ventilation request and is waiting to get confirmation from another Pelican device that the cycle is active.

(Video) How to bypass Honeywell temperature limiter for your thermostat! Thermostat Hack!Thermostat Override
(The Weekend DIYer)
How do I get my Honeywell thermostat off wait?

The "Wait" message on a Honeywell Thermostat means the thermostat is waiting to activate the HVAC system. This is done to prevent damaging the HVAC system compressor. If the system is working properly, then "Wait" should disappear after a few minutes. It will then resume normal operation.

(Video) Thermostat Reset
(The Flats at Ridgeview)
How do I get my Honeywell thermostat wait to go away?

When your Honeywell thermostat says wait for longer than five minutes, it is likely that you are encountering a voltage issue. You can attempt to reset the thermostat by installing new batteries in it. With fresh batteries at their peak voltage, you have a clearer idea of what may be behind your long wait status.

(Video) What is permanent hold on Honeywell thermostat?
(People·WHYS)
How long does hold last on Honeywell thermostat?

A temporary hold will keep the HVAC system set to the held temperature for a temporary period of time of less than 12 hours or until the hold is cancelled. A permanent hold will keep the HVAC system set to the held temperature permanently, until the hold is cancelled.

(Video) No power to Honeywell thermostat? Here's a fix.
(Chris McDowell)
Should you keep your thermostat on hold?

Keeping your home at a constant temperature generally means that your HVAC system will run constantly to meet it. This means that your furnace or air conditioner may run when you're asleep, at work, or out of the house. This wastes more energy than the minimal amount that you might save by having it constantly run.

(Video) Honeywell 9000 wifi thermostat waiting for update
(wifi thermostat / Thermostat Forums.com)
Why won t my honeywell thermostat turn on heat?

Troubleshooting a Programmable Honeywell Thermostat

Put in new batteries; Check the circuit breaker; Check the indoor unit to make sure all the panel doors are closed; Make sure the power is connected to the furnace or air conditioning unit by checking the switch near the indoor unit is up.

(Video) How to removed the schedule off the Honeywell Vision Pro WIFI
(Hollywood Maintenance)

Why is my Honeywell your thermostat not communicating?

Try the following: Make sure your app is up to date and your mobile phone is within 3-5 feet of your thermostat. Restart your mobile device and turn off any apps that may enhance the security, including VPN's, GPS spoofers, etc. These can be turned on again once the connection of the thermostat is complete.

(Video) HVAC Thermostat Blinking Cool On But A/C Not Working
(Word of Advice TV)
What are the signs of a bad thermostat?

You'll need to look out for the following signs:
  • Overheating (or overcooling)
  • Coolant leaking.
  • Erratic temperature changes.
  • Strange sounds.
  • Heater problems.
Sep 19, 2022

Honeywell thermostat says wait? (2024)
Why is my thermostat not communicating with my unit?

Try replacing the batteries, then check for a blown fuse or tripped breaker in the electrical panel. If the thermostat is still unresponsive, make sure the breaker is shut off and remove the cover.

What does a stuck thermostat do?

One of the most prevalent symptoms of thermostat failure is irregular operating temperatures. A stuck closed thermostat will cause engine temperatures to skyrocket, while a stuck open thermostat will cause an engine to run cool.

Why is my thermostat not setting?

Your Vents Are Blocked

Your thermostat will not be able to reach your desired temperature if you have something blocking the vents. Check the vents around your home and make sure you do not have any items such as furniture in the way of your vent's airflow. While you're at it, make sure all of your vents are open.

How do I clear the hold on my thermostat?

This is where the “Hold” button on your thermostat comes into play. By pressing “Hold”, your thermostat will lock in the temperature it's currently at until you change it again. When you are ready for your normal schedule to resume, simply press the “Run” button and return to your typical programming.

What is temporary hold or permanent hold on Honeywell thermostat?

What is temporary hold? The temporary hold setting is when you change the temperature setting to a different temperature and it stays at that setting until the next schedule change. The permanent hold setting holds the temperature setting you have chosen for an indefinite time. This overrides your scheduled settings.

How do I reset my Honeywell thermostat effortlessly in seconds?

How to Reset the Machine Manually.
  1. Press the up and fan button simultaneously. Continue pressing them together.
  2. In the meantime, change the right number to 1 and that of the left to 90.
  3. Now, press “Done”. You will have a reset machine.
Dec 29, 2021

Why won t my Honeywell thermostat cool down?

Verify that the thermostat is switched to cool mode and has a cooling set point below the room temperature reading. Check the thermostat display for cooling, usually indicated by the words “cool on” or a snowflake icon. If these icons are flashing, the thermostat is in delay mode, which can last up to 5 minutes.

What is the lowest temp to leave thermostat?

If you're going to be leaving your home or traveling for the winter, it's best to keep your thermostat set no lower than 55 degrees. If you don't, you could risk having your pipes freeze over.

What is the most efficient temperature to keep your house at?

What temperature should you keep your house at? Or better yet, “What is the most energy saving temperature to set my thermostat at?” According to ENERGYSTAR.gov, the ideal home temperature should be between 70 to 78 degrees Fahrenheit.

Should the thermostat be on auto or on?

Keeping your thermostat in the AUTO position means less overall energy is being used—and that reduces your utility bills considerably. Not only that, your air filter will last longer than they will if you leave your fan running continuously—in other words, if you leave it in the “on” position.

Why is my thermostat not switching heating?

Firstly, try changing the batteries. If that has no effect, the thermostat might be suffering from faulty wiring or a broken sensor. If it's a newer digital thermostat, reset it and start over again. If you've installed it recently, run through the setup process again.

How do you know if your Honeywell thermostat is working?

Thermostat Functionality

Go to your thermostat and switch from Heating to Cooling and then feel the temperature of the air blowing from the vent. If COLD, this means your thermostat is cooling correctly, but the heating isn't working properly. Contact Support at 1-855-733-5465 to find a pro-installer in your area.

How do I reset my Honeywell thermostat manually?

Here's how:
  1. Power off the thermostat and remove the batteries.
  2. Put the batteries in the wrong way, with negative to positive and positive to negative.
  3. Wait ten seconds and put them back in the correct way.
  4. Your thermostat will be reset to factory settings. Be sure to reprogram your thermostat to your normal schedule.

Why is my thermostat and furnace not communicating?

Check the Power Source Sometimes the problem between the thermostat and your furnace is as simple as replacing the batteries. Many digital thermostats use standard batteries to power their functions. Also make sure to check there is power at the furnace as well.

How much does it cost to replace a bad thermostat?

Thermostat replacement typically costs between $120 and $330, or around $210 on average. The cost of a new thermostat tends to be around $210 nationwide, with most homeowners spending between $120 and $330, including installation.

How can I test my thermostat?

Step-by-step Guide for Testing Your Thermostat
  1. Step 1: Check to See that the Thermostat Is Receiving Power. ...
  2. Step 2: Make Sure the Thermostat Is Set to the Proper Settings. ...
  3. Step 3: Turn Up The Heat. ...
  4. Step 4: Turn Off The Power to the Furnace. ...
  5. Step 5: Remove the Thermostat Cover. ...
  6. Step 6: Check the Wiring of the Thermostat.
Feb 28, 2022

Can a bad thermostat cause the AC unit not to work?

When your thermostat is working correctly, you can keep it as cool or warm as you need. A bad thermostat can cause your AC to not cool or heat the room to the desired temperature. Air conditioning concerns are more apparent: Your thermostat is one of the best indicators of your air conditioning system's health.

How can you tell if a thermostat is bad without removing it?

If you find the coolant is flowing, it means the thermostat valve is open. This is usually a good indicator of if you need to replace your car thermostat. If you notice the coolant is not flowing, wait until your car's engine has reached the operating temperature.

Does resetting a thermostat help?

Just like your cable modem, a digital thermostat needs a reset every once in a while to kick it back into shape and set it in proper working order. You will know when a reset is necessary because your thermostat will not be regulating the temperature of your home as well as it was before.

How long do thermostats last?

Modern home thermostats tend to have about a 10-year lifespan but are usually replaced sooner due to innovations in the market. Non-programmable thermostats have become outdated and replaced by programmable (or learning) thermostats.

What happens if I push the reset button on my thermostat?

It will turn the thermostat off, and in most cases, it will restore the thermostat to factory settings. If you're experiencing problems with your HVAC system, you should try using the reset button. If that doesn't work, you can always contact an HVAC technician for assistance.

What is the problem if thermostat is not working?

One of the most common reasons why thermostats don't work is dead batteries. If the batteries your the thermostat are dead, the thermostat will not be functional. Therefore, you will need to replace its batteries. If the thermostat still does not work after you do this, you may need to call a professional for help.

How long should it take to cool a house from 80 to 72?

It usually takes around two and a half to three and a half hours to cool your house from 80 to 72 degrees. However, a variety of different factors can affect the time it takes to reach the desired temperature, including the thermostat setting, the size of the house, and the efficiency of the air filters.

How long is a thermostat delay?

The delay is usually just a few minutes, but it's there to help your system. Many thermostat brands and models also use the maintenance band to help prevent system wear.

How long does it take for thermostat to kick in?

From a cold start, your vehicle's thermostat will stay closed and you won't notice any coolant flowing into your radiator. Leave the vehicle running for about 10-20 minutes so it can reach its optimal running temperature.

How long is a temporary hold on a thermostat?

A temporary hold will keep the HVAC system set to the held temperature for a temporary period of time of less than 12 hours or until the hold is cancelled. A permanent hold will keep the HVAC system set to the held temperature permanently, until the hold is cancelled.

How long should it take for a thermostat to open?

On average, 2–5 minutes and the thermostat should be opening. If you have a responsive water temp gauge, you can see a slight dip in temperature as the coolant starts to flow.

What is the delay setting on a Honeywell thermostat?

Check the thermostat display for cooling, usually indicated by the words “cool on” or a snowflake icon. If these icons are flashing, the thermostat is in delay mode, which can last up to 5 minutes. This delay protects your equipment from short cycling.

Why is my Honeywell thermostat not working?

Troubleshooting a Programmable Honeywell Thermostat

Put in new batteries; Check the circuit breaker; Check the indoor unit to make sure all the panel doors are closed; Make sure the power is connected to the furnace or air conditioning unit by checking the switch near the indoor unit is up.

Why is my thermostat temp not going up?

Your Vents Are Blocked

Your thermostat will not be able to reach your desired temperature if you have something blocking the vents. Check the vents around your home and make sure you do not have any items such as furniture in the way of your vent's airflow. While you're at it, make sure all of your vents are open.

How would you know if your thermostat is bad?

Constant Temperature Shifts

A faulty thermostat typically has a hard time maintaining settings. It may continuously change temperature settings without warning. Try lowering the thermostat settings for a test trial and see what happens. If the same problem occurs, call a technician to check the thermostat.

Should I keep my thermostat on permanent hold?

Instead of choosing a constant temperature year-round, it's better to keep your house a constant temperature on a seasonal basis. Keeping your home at a higher temperature during the warmer months will mean your air conditioner doesn't have to work as hard.

What is the difference between temporary and hold on a Honeywell thermostat?

The temporary hold setting is when you change the temperature setting to a different temperature and it stays at that setting until the next schedule change. The permanent hold setting holds the temperature setting you have chosen for an indefinite time. This overrides your scheduled settings. Was this article helpful?

Should you put thermostat on hold?

When to Set Your Thermostat to Hold. You should consider setting your thermostat to hold whenever you want to temporarily override its heating and cooling schedule. Programmable thermostats are convenient. Instead of manually adjusting the temperature each day, you can program a schedule.

What tells the thermostat to open?

At low temperatures, the outlet to the radiator is completely blocked -- all of the coolant is recirculated back through the engine. Once the temperature of the coolant rises to between 180 and 195 F (82 - 91 C), the thermostat starts to open, allowing fluid to flow through the radiator.

Can a thermostat slowly go bad?

Your car, truck, utility vehicle, or van's thermostat is responsible for releasing coolant into the engine once it starts to get too hot. This temperature gauge can go bad after about 10 years, so if you drive an older automobile, it's a good idea to know the signs that the thermostat is having problems.

How much does it cost to replace a thermostat?

Thermostat replacement typically costs between $120 and $330, or around $210 on average. The cost of a new thermostat tends to be around $210 nationwide, with most homeowners spending between $120 and $330, including installation.

References

You might also like
Popular posts
Latest Posts
Article information

Author: Rev. Leonie Wyman

Last Updated: 10/04/2024

Views: 6063

Rating: 4.9 / 5 (59 voted)

Reviews: 82% of readers found this page helpful

Author information

Name: Rev. Leonie Wyman

Birthday: 1993-07-01

Address: Suite 763 6272 Lang Bypass, New Xochitlport, VT 72704-3308

Phone: +22014484519944

Job: Banking Officer

Hobby: Sailing, Gaming, Basketball, Calligraphy, Mycology, Astronomy, Juggling

Introduction: My name is Rev. Leonie Wyman, I am a colorful, tasty, splendid, fair, witty, gorgeous, splendid person who loves writing and wants to share my knowledge and understanding with you.